| Welcome to the Rx7 Forum and Owners Club. |
|
|
If this is your first visit, be sure to check out the FAQ by clicking the link above.
You may have to register before you can post: click the register link above to proceed.
To start viewing messages, select the forum that you want to visit from the selection below.
<<<<<< Register to remove these ads >>>>>>
|
|
| 3rd Generation 1993-Current Discussion |
03-05-2004, 07:02 AM
|
#1
|
|
Junior Member
Join Date: Mar 2004
Posts: 1
|
New engine
Hello,
I have a freind that is getting an engine rebuilt. The engine will be returned ready to drop in. I am looking for a list of parts that should be replaced at this time, including sensors, harnesses, mounts , lines etc. Also, I need a recommendatin for where to order these Mazda parts. The local dealership is incredibly expensive. Thanks in advance for the response, and this is of course for a 3rd gen.
Darrell P
|
|
|
|
|
|
03-05-2004, 06:15 PM
|
#2
|
|
Administrator
Join Date: Feb 2004
Age: 48
Posts: 779
|
Nice of you to join .z,
Well, have you searched on the net? There are some good places out there but they usually have a high shipping cost.
What type/size of engine is he rebuilding? That will be a helpful thing to know when searching for the parts you need.
Let me know.
Shagg
|
|
|
|
|
|
|
05-08-2004, 01:38 AM
|
#3
|
|
Full Access Member
Join Date: May 2004
Posts: 170
|
all the hoses, vac lines, coolant lines ect.
might as well change the water pum and thermostat.
basic tune up stuff, plugs wires ect.
maybe the clutch, its always easier with the motor out
also inspect the motor mounts. (I know a guy who makes solid mounts kit)
|
|
|
|
|
|
|
05-08-2004, 02:49 AM
|
#4
|
|
Full Access Member
Join Date: Mar 2004
Location: Miami
Posts: 319
|
solid mounts suck... just make sure all the vacuum hoses are in good condition, I also wanted to say that if he doesnt know what he's doing then he shouldnt be involved in installing the engine... 13brew is a very conplex engine, there are tons of solenoids required for running the sequencial setup... so im just hoping he knows what he's doing..
|
__________________
|
|
|
|
|
05-08-2004, 06:07 PM
|
#5
|
|
Full Access Member
Join Date: Apr 2004
Location: Austin & Waco Texas
Posts: 553
|
.z replace all of the vacuum hosing, replace the belts, replace the vacuum caps, replace all of the hosing in general. Change all squeeze clamps to screw clamps because squeeze clamps are entirely useless. Change the oil once it's in. drive for a day or two, change the oil again, finish out 2 or 3 weeks, then change it again. Don't wail on it yet.
|
|
|
|
|
|
|
05-09-2004, 04:09 PM
|
#6
|
|
Full Access Member
Join Date: May 2004
Posts: 170
|
whats wrong with solid mounts? I noticed a big difference with them, smoother on the hwy, the car is much more responsive and .2 off 60 ft.
|
|
|
|
|
|
|
05-09-2004, 07:12 PM
|
#7
|
|
Full Access Member
Join Date: Apr 2004
Location: Austin & Waco Texas
Posts: 553
|
You must've had terrible mounts before that then
|
|
|
|
|
|
|
05-09-2004, 07:34 PM
|
#8
|
|
Full Access Member
Join Date: May 2004
Posts: 170
|
they were about a year old when I replaced them with the solids
|
|
|
|
|
|
|
05-10-2004, 12:21 AM
|
#9
|
|
Full Access Member
Join Date: Apr 2004
Location: Austin & Waco Texas
Posts: 553
|
Hmm, what type of material were the previous ones?
|
|
|
|
|
|
|
05-10-2004, 01:32 AM
|
#10
|
|
Full Access Member
Join Date: May 2004
Posts: 170
|
stock from mazda
|
|
|
|
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
Linear Mode
